check_smart monitoring plugin
Full and up to date documentation
Please go to https://www.claudiokuenzler.com/monitoring-plugins/check_smart.php for a complete and updated documentation including changelog, extensive usage examples, monitoring configurations (including Nagios, Icinga 1, Icinga 2, Shinken and Naemon).
Introduction
This is a plugin to monitor the health and values of SMART attributes of hard (HDD), solid state (SSD) and NVMe drives. The plugin is a fork of check_smart released in 2009 by Kurt Yoder. Since then the plugin has undergone a lot of changes. It allows to monitor drives behind hardware controllers and added a lot of parameters to fine tune the checks and set thresholds (on a per attribute setting).
Sudoers entry
This plugin needs to run as root, otherwise you're not able to lauch smartctl correctly. You have two options
1) Launch the plugin itself as root with sudo
2) Lauch the plugin as Nagios user and the smartctl command as root with sudo
Entry in sudoers (of course adapt your paths if necessary):
nagios ALL = NOPASSWD: /usr/lib/nagios/plugins/check_smart.pl # for option 1
nagios ALL = NOPASSWD: /usr/local/sbin/smartctl # for option 2Successful tests/examples
SATA disk behind MDRaid (Software Raid) on Linux:
/usr/lib/nagios/plugins/check_smart.pl -d /dev/sda -i ataMegaRAID on Linux:
/usr/lib/nagios/plugins/check_smart.pl -d /dev/sda -i megaraid,8Intel RAID on FreeBSD 9.2 ("kldload mfip.ko" required):
/usr/local/libexec/nagios/check_smart.pl -d /dev/pass0 -i scsiSATA drives behind Intel RAID on FreeBSD 9.2 ("kldload mfip.ko" required):
/usr/local/libexec/nagios/check_smart.pl -d /dev/pass12 -i satSCSI drives behind HP RAID (CCISS) on FreeBSD 6.0:
/usr/local/libexec/nagios/check_smart.pl -d /dev/ciss0 -i cciss,0
OK: no SMART errors detected|defect_list=0 sent_blocks=3093462752 temperature=24;;68
/usr/local/libexec/nagios/check_smart.pl -d /dev/ciss0 -i cciss,3
WARNING: 48 Elements in grown defect list | defect_list=48 sent_blocks=1137657348 temperature=22;;68Using threshold option (-b) to ignore 1 bad element, warning only when 2 bad elements are found:
/usr/local/libexec/nagios/check_smart.pl -d /dev/ciss0 -i cciss,1 -b 2
OK: 1 Elements in grown defect list (but less than threshold 2)|defect_list=1;2;2;; sent_blocks=2769458900762624 temperature=27;;65SCSI drives behind HP RAID (CCISS) on Linux (Ubuntu hardy):
/usr/lib/nagios/plugins/check_smart.pl -d /dev/cciss/c0d0 -i cciss,0
OK: no SMART errors detected. |Check all SATA disks (sda - sdz) at the same time on Linux:
/usr/lib/nagios/plugins/check_smart.pl -g "/dev/sd[a-z]" -i ata
OK: [/dev/sda] - Device is clean --- [/dev/sdb] - Device is clean|Check all SCSI disks behind Intel RAID on FreeBSD 9.2 ("kldload mfip.ko" required):
/usr/local/libexec/nagios/check_smart.pl -g /dev/pass[1-9] -i scsi
OK: [/dev/pass0] - Device is clean --- [/dev/pass1] - Device is clean --- [/dev/pass2] - Device is clean --- [/dev/pass3] - Device is clean --- [/dev/pass4] - Device is clean --- [/dev/pass5] - Device is clean --- [/dev/pass6] - Device is clean --- [/dev/pass7] - Device is clean --- [/dev/pass8] - Device is clean --- [/dev/pass9] - Device is clean | Single SCSI drive on FreeBSD 10.1:
/usr/local/libexec/nagios/check_smart.pl -d /dev/da0 -i scsi
OK: no SMART errors detected. |sent_blocks=14067306 temperature=34;;60Single NVMe drive on Linux:
/usr/lib/nagios/plugins/check_smart.pl -d /dev/nvme0 -i nvme
OK: Drive Samsung SSD 970 PRO 512GB S/N XXXXXXXXXXXXXXX: no SMART errors detected. |Temperature=34 Available_Spare=100 Available_Spare_Threshold=10 Percentage_Used=0 Data_Units_Read=2854 Data_Units_Written=107590 Host_Read_Commands=67150 Host_Write_Commands=1406316 Controller_Busy_Time=20 Power_Cycles=16 Power_On_Hours=105 Unsafe_Shutdowns=6 Media_and_Data_Integrity_Errors=0 Error_Information_Log_Entries=0 Warning__Comp._Temperature_Time=0 Critical_Comp._Temperature_Time=0 Temperature_Sensor_1=34 Temperature_Sensor_2=33see https://www.claudiokuenzler.com/monitoring-plugins/check_smart.php for more examples
